3D Printing: Difference between revisions

From Unallocated Space
Jump to navigation Jump to search
No edit summary
(4 intermediate revisions by 2 users not shown)
Line 8: Line 8:
= List of parts to purchase=
= List of parts to purchase=


==Mechanical==
[[3d_printer_parts]]
{| class="wikitable"
|-
! Quantity
! Item
! Link
! Note
! Purchased
|-
| 1
| pane of glass 7 7/8"x 7-7/8"
| None
| None
| No
|-
| 1
| Plastruder
| [http://www.makergear.com/products/plastruder]
| 1.75mm filament
| No
|-
| 83
| 5/16" Nuts
| [http://www.lowes.com/pd_56106-37672-35002_0__?productId=3035552&Ntt=m8+nut+100+count&pl=1&currentURL=%2Fpl__0__s%3FNtt%3Dm8%2Bnut%2B100%2Bcount&facetInfo=]
| Stainless
| No
|-
| 93
| 5/16" Washers
| [http://www.lowes.com/pd_1990-37672-35007_0__?productId=3019934&Ntt=m8+washer+100+count&pl=1&currentURL=%2Fpl__0__s%3FNtt%3Dm8%2Bwasher%2B100%2Bcount%26page%3D2&facetInfo=]
| Stainless
| No
|-
| 6
| 5/16" x 30 Fender Washers
| unknown
| Stainless
| No
|-
| 2
| M4 x 20 Bolt
| Link
| Note
| No
|-
| 2
| M4 Nut
| Link
| Note
| No
|-
| 2
| M4 Washer
| Link
| Note
| No
|-
| 22
| M3 x 10 Bolt
| Link
| Note
| No
|-
| 16
| M3 x 25 Bolt
| Link
| Note
| No
|-
| 4
| M3 x 40 Bolt
| Link
| Note
| No
|-
| 70
| M3 Washer
| Link
| Note
| No
|-
| 40
| M3 Nut
| Link
| Note
| No
|-
| 2
| M3 Grub Screw
| Link
| Note
| No
|-
| 3
| 608 Roller Skate Bearing
| [http://www.vxb.com/page/bearings/PROD/608ZZ10-1]
| Note
| No
|-
| 6
| 5/16" x 370mm Threaded Rod
| Link
| Note
| No
|-
| 4
| 5/16" x 294mm Threaded Rod
| Link
| Note
| No
|-
| 3
| 5/16" x 440mm Threaded Rod
| Link
| Note
| No
|-
| 2
| 5/16" x 210mm Threaded Rod
| Link
| Note
| No
|-
| 1
| 5/16" x 50mm Threaded Bolt
| Link
| Note
| No
|-
| 2
| Everbilt 1/2 in. x 1-1/2 in. and 7/16 in. x 2-1/8 in. Zinc-Plated Compression Springs (4-Pack)
| [http://www.homedepot.com/h_d1/N-5yc1v/R-202045476/h_d2/ProductDisplay?langId=-1&storeId=10051&catalogId=10053]
| Needed for the threaded rods
| No
|-
| 2
| 8mm x 420mm Smooth Rod
| Link
| Note
| No
|-
| 4
| 8mm x 406mm Precision Rod
| [http://www.vxb.com/Merchant2/merchant.mvc?Screen=PROD&Store_Code=bearings&Product_Code=kit11867]
| Note
| No
|-
| 2
| 8mm x 330 mm Precision Rod
| [http://www.vxb.com/Merchant2/merchant.mvc?Screen=PROD&Store_Code=bearings&Product_Code=kit11868]
| Note
| No
|-
| 1
| 225mm x 225mm
| Link
| Steel
| No
|-
| 1
| 140mm x 225mm
| Link
| Steel
| No
|-
| 1
| 840mm x 5mm Belt
| [http://www.mcmaster.com/#57105k11/=eu7gde]
| Rubber
| No
|-
| 1
| 900mm x 5mm Belt
| [http://www.mcmaster.com/#57105k11/=eu7gde]
| Rubber
| No
|-
| 5
| NEMA Bi-Polar Stepper Motor
| [http://www.lulzbot.com/en/48-nema-17-stepper-motors.html]
| Recommended by Midsouth Makers
| No
|-
| 50
| Zip Ties
| Link
| Small
| No
|-
| 1
| Maker Gear Plastruder
| [http://www.makergear.com/products/plastruder] - $170
| Prusa Stepper Plastruder Kit (.35mm hybrid for 1.75mm filament)
| No
|-
|2
| Pully
| [http://www.mcmaster.com/#57105k11/=eu7gde]
| Recommended by Midsouth Makers
| No
|-
|1
| Hobbled Bolt
| [http://www.lulzbot.com/en/7-hobbed-bolts.html]
| Recommended by Midsouth Makers
| No
|}
 
==Electronic==
{| class="wikitable"
|-
! Quantity
! Item
! Link
! Note
! Purchased
|-
| <del>1</del>
| <del>Heated Bed</del>
| <del>[http://ultimachine.com/content/prusa-pcb-heated-bed] $50.00</del>
| <del>Recommended by Midsouth Makers</del>
| YES
|-
| <del>1</del>
| <del>RAMPS DIY Kit</del>
| <del>[http://ultimachine.com/content/ramps-diy-kit-complete] $162.00</del>
| <del>Recommended by Midsouth Makers</del>
| YES
|}


= Purchased Parts with Links=
= Purchased Parts with Links=
Line 248: Line 20:
NEMA17 Stepper Motors: [http://www.a2aprinter.com/index.php?route=product/product&path=33&product_id=51]
NEMA17 Stepper Motors: [http://www.a2aprinter.com/index.php?route=product/product&path=33&product_id=51]


=Cost of 3DPrinter=
*Printed Parts = $50
*PRUSA PCB Heated Bed from UltiMachine $55.00 + $8.68 Shipping = Total $63.68
*Hardware Kit and Stepper Motors from A2APrinter $115.63 + $88.95 + $49.42 Shipping = $253.99
*RAMPS DIY Kit was purchased by a member of the space, I will update when I have real numbers
*Prusa Stepper Plastruder from MakerGear $170.00 + $7.48 Shipping = Total $177.48
*Hobbled Bolt from LulzBot $7.00 + $5.60 Shipping = Total $12.60
Total for all parts including shipping: $557.75 + RAMPS DIY Kit
= Assembly =
Why re-invent the wheel, RepRap offers a beautiful instruction page.
Please check [http://reprap.org/wiki/Prusa_Mendel_Assembly]for instructions.


= Ideas in the works =
= Ideas in the works =
Line 261: Line 48:


1/19/2012
1/19/2012
I placed the order for the heated bed
I have submitted a list from McMaster Carr to our friends at Midsouth Makers for them to review
I have ordered the Plastruder from MakerGear
Total in Donations has gone up by $160 for a total of $260 donated to the project
Total in Donations has gone up by $160 for a total of $260 donated to the project
*LulzBot Order #000499 - Hobbled Bolt
*MakerGear Order #5904 - Plastruder
*A2A Printer Order ID: 71 - Stepper Motors and Hardware kit
*UltiMachine Order #6446 - Heated Bed
=Common Problems=
If you receive the following error message when launching Cura from Terminal, or nothing happens when you launch Cura through the GUI, do this:
Error message: /usr/share/cura-lulzbot/cura-lulzbot: /lib/x86_64-linux-gnu/libc.so.6: version `GLIBC_2.28' not found (required by /usr/share/cura-lulzbot/cura-lulzbot)
Solution: In terminal, run the command "sudo apt remove -y cura-lulzbot && sudo apt install -y cura-lulzbot=3.2.32" (without quotes) .
If you cannot save a profile in Cura, make sure you own all the files/directories in your home folder. We had this issue when someone ran it using sudo.
Solution: sudo chmod -R unallocatedspace:unallocatedspace ~/

Revision as of 17:13, 17 August 2019

Unallocated Space has acquired the parts to start building a 3D printer called a RepRap Prusa Mendel.

This bot will be a valuable addition to the space and can be used as a source of custom one off parts as well as fun odds and ends.

The 3D printing initiative will be headed up by Hexjunkie, please see him if you have any questions.


List of parts to purchase

3d_printer_parts

Purchased Parts with Links

Prusa Mendel Hardware Kit: [1] Prusa Mendel Printed Parts: [2] RAMPS DIY Kit: [3] Heated Print Bed: [4] Plastruder: [5] Hobbled Bolt: [6] NEMA17 Stepper Motors: [7]

Cost of 3DPrinter

  • Printed Parts = $50
  • PRUSA PCB Heated Bed from UltiMachine $55.00 + $8.68 Shipping = Total $63.68
  • Hardware Kit and Stepper Motors from A2APrinter $115.63 + $88.95 + $49.42 Shipping = $253.99
  • RAMPS DIY Kit was purchased by a member of the space, I will update when I have real numbers
  • Prusa Stepper Plastruder from MakerGear $170.00 + $7.48 Shipping = Total $177.48
  • Hobbled Bolt from LulzBot $7.00 + $5.60 Shipping = Total $12.60

Total for all parts including shipping: $557.75 + RAMPS DIY Kit

Assembly

Why re-invent the wheel, RepRap offers a beautiful instruction page.

Please check [8]for instructions.

Ideas in the works

Ongoing Projects

UPDATES

To date we have had a total of 1 major purchase made to the project: the RAMPS DIY Kit I have created a parts list from McMaster Carr that I am verifying now. I should place the order this month.(January 2012) The project has received a total of $100 in cash donations.

1/19/2012 Total in Donations has gone up by $160 for a total of $260 donated to the project

  • LulzBot Order #000499 - Hobbled Bolt
  • MakerGear Order #5904 - Plastruder
  • A2A Printer Order ID: 71 - Stepper Motors and Hardware kit
  • UltiMachine Order #6446 - Heated Bed

Common Problems

If you receive the following error message when launching Cura from Terminal, or nothing happens when you launch Cura through the GUI, do this:

Error message: /usr/share/cura-lulzbot/cura-lulzbot: /lib/x86_64-linux-gnu/libc.so.6: version `GLIBC_2.28' not found (required by /usr/share/cura-lulzbot/cura-lulzbot)

Solution: In terminal, run the command "sudo apt remove -y cura-lulzbot && sudo apt install -y cura-lulzbot=3.2.32" (without quotes) .

If you cannot save a profile in Cura, make sure you own all the files/directories in your home folder. We had this issue when someone ran it using sudo.

Solution: sudo chmod -R unallocatedspace:unallocatedspace ~/

Retrieved from "https://www.wiki.unallocatedspace.org/wiki/index.php?title=3D_Printing&oldid=940"