Arduino Night

This class will change from starting at 7 to starting at 6. If this does not work for you, please contact the E-Mail address at the bottom. We are fairly flexible with the time. Also, if enough people chip in, we can order some food.

Agenda

1. DIY Arduino Build 2. Fading LEDs with transistors 3. 7 segment displays 4. Multiplexers as port expanders

After the DIY Arduino, we will cover as much of items 2-4 as possible.

For the DIY Arduino there will be kits for $12 with the following parts

No. Qty. Description 1 IC, ATmega328P, DIP-28, Optiboot bootloader /2129334 1 Socket, IC, 28-pin, 0.3" 1 IC, 5V regulator, 7805T 1 LED, Red, 660nm, T1-3/4 (Replaced 334035) 1 LED, Green, 565nm, T1-3/4 1 Resistor, 1/4W, 10K Ω 2 Resistor, 1/4W, 180 Ω 2 Capacitor, radial, 10µF, 50V 1 Crystal, 16 MHz, low-profile 2 Capacitor, ceramic disc, 22pF, 50V 1 Capacitor, ceramic disc, 0.1µF, 50V 1 Switch, pushbutton, OFF-(ON) 1 Header, 6-pin, 1-row, vertical, 0.1" 1 IC, 3.3V regulator, LM1117T-3.3 2 Capacitor, tantalum, 10µF, 25V 1 9v Power Connectors

Requirements 1. Arduino or kit from topic 1 (only needed for topics 2-4) 2. Breadboard (there might be a few available) 3. Jumper wires for breadboarding

Provided 1. Arduino Uno Kits (parts listed above) for $12 2. FTDI Cable to Use and/or Buy 3. Extra Headers, 9v Power Connectors to Use and/or Buy 4. 9v Batteries to Buy 5. 7 segment displays (approx 6) 6. Multiplexer boards (only 3) https://www.sparkfun.com/products/9056 7. Transistors (P2N2222)

If there are any questions, comments, suggestions, etc then please contact Proto17 at dmp250net@gmail.com.

Arduino Night 2

Agenda: 1. Transistors for LEDs and motors (a repeat, but really important!) 2. Shift registers to control LEDs (and possibly 7 segment displays) 3. Using tactile switches (including de-bouncing) 4. Talking to other Arduinos

(I do not expect to get to number 4, but it's there if we do!)

Required Items: 1. Breadboard (please let me know if you need one as I have several to borrow) 2. Arduino (any kind will work, including the DIY builds) 3. Laptop (please let me know if you need one as the space has about 3) 4. Jumper wires 5. 9 volt battery (for the transistor portion)

Provided Items: 1. LEDs (red/green and single color) 2. 7 segment display (mix of common cathode and common anode) 3. Shift register (74HC595) 4. Tactile switch 5. 2N2222A transistor

If you would like a shift register of your own, please let me know. I ordered 10 for the last class and will happily part with them for a $1 donation to the space. For those of you who would like to order one prior to the class, the part number is 74HC595. Available from Jameco, Mouser, DigiKey, Adafruit, and SparkFun. I am fairly certain that we have several at the space as well.

Since the space runs off of donations, we would like to mention that the recommended donation for this class is $10. It is by no means a requirement! Attendance to the space and this class is, as usual, 100% free to all! And a huge thank you to those of you who donated last time!

For questions/comments, please contact uas.arduino@gmail.com.

Hope to see you all there :)

Oh, and here are some links for the "Available from Jameco, Mouser, DigiKey, Adafruit, and SparkFun" part:

http://www.jameco.com/webapp/wcs/stores/servlet/Product_10001_10001_46105_-1 http://www.mouser.com/ProductDetail/NXP-Semiconductors/74HC595N112/?qs=sGAEpiMZZMvKM5ialpXrmr5J3bDXowCz http://www.digikey.com/product-detail/en/SN74HC595N/296-1600-5-ND/277246 https://www.adafruit.com/products/450 https://www.sparkfun.com/products/733

External code links

Various code snippets used during class - http://pastebin.com/u/uas_arduino

Classes

1) Here we go again -done

2) Digital Write

3) Digital Read

4) Analog Write

5) Analog Read

6) Serial

7) Interrupts

8) ShiftOut In

9) I2C

10) SPI

11)

12)

13)