3D Printing: Difference between revisions
| (7 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
Unallocated Space has two main 3D printers set up for use. The | Unallocated Space has two main 3D printers set up for use. The Creality K1 Max and Creality CR-10. | ||
These are connected to a laptop with the Cura slicer software. | These are connected to a laptop with the Cura slicer software. | ||
| Line 5: | Line 5: | ||
= Printers = | = Printers = | ||
== [[ | == [[3D Printers:Creality K1 Max|Creality K1 Max]] == | ||
[https://www.creality.com/products/creality-k1-max-3d-printer Manufacture Page] | [https://www.creality.com/products/creality-k1-max-3d-printer Manufacture Page] | ||
Nozzle size: 4mm, 6mm | Nozzle size: 4mm, 6mm | ||
Nozzle material: Brass plated wear resistant | Nozzle material: Brass plated wear resistant | ||
Hotend: Micro Swiss FlowTech | Hotend: Micro Swiss FlowTech | ||
Filament size: 1.75mm | Filament size: 1.75mm | ||
Supported filamnet: ABS/PLA/PETG/PET/TPU/PA/ABS/ASA/PC PLA-CF/PA-CF/PET-CF | Supported filamnet: ABS/PLA/PETG/PET/TPU/PA/ABS/ASA/PC PLA-CF/PA-CF/PET-CF | ||
Build Volume: 300x300x300mm | Build Volume: 300x300x300mm | ||
| Line 21: | Line 27: | ||
Filament size: 1.75mm | Filament size: 1.75mm | ||
Supported filament: PL/PETG/TPU/wood | Supported filament: PL/PETG/TPU/wood | ||
| Line 31: | Line 38: | ||
Won in an essay contest. | Won in an essay contest. | ||
== Legacy Printers == | == Legacy Printers == | ||
* [[ | * [[3D Printers:RepRap Prusa|RepRap Prusa]] | ||
* [[3D Printers:Lulzbot Taz 3|Lulzbot Taz 3]] | |||
= Common Problems = | = Common Problems = | ||
| Line 54: | Line 54: | ||
Solution: sudo chmod -R unallocatedspace:unallocatedspace ~/ | Solution: sudo chmod -R unallocatedspace:unallocatedspace ~/ | ||
[[Category:Station]] | [[Category:Station]] | ||
Latest revision as of 07:40, 13 May 2024
Unallocated Space has two main 3D printers set up for use. The Creality K1 Max and Creality CR-10.
These are connected to a laptop with the Cura slicer software.
Printers
Creality K1 Max
Nozzle size: 4mm, 6mm
Nozzle material: Brass plated wear resistant
Hotend: Micro Swiss FlowTech
Filament size: 1.75mm
Supported filamnet: ABS/PLA/PETG/PET/TPU/PA/ABS/ASA/PC PLA-CF/PA-CF/PET-CF
Build Volume: 300x300x300mm
Creality CR-10s
Filament size: 1.75mm
Supported filament: PL/PETG/TPU/wood
Bed size: 300mm × 300mm × 400mm
Lulzbot Mini 1
Bed size: 152mm x 152mm x 158mm
Won in an essay contest.
Legacy Printers
Common Problems
If you receive the following error message when launching Cura from Terminal, or nothing happens when you launch Cura through the GUI, do this:
Error message: /usr/share/cura-lulzbot/cura-lulzbot: /lib/x86_64-linux-gnu/libc.so.6: version `GLIBC_2.28' not found (required by /usr/share/cura-lulzbot/cura-lulzbot)
Solution: In terminal, run the command "sudo apt remove -y cura-lulzbot && sudo apt install -y cura-lulzbot=3.2.32" (without quotes) .
If you cannot save a profile in Cura, make sure you own all the files/directories in your home folder. We had this issue when someone ran it using sudo.
Solution: sudo chmod -R unallocatedspace:unallocatedspace ~/