This is the list of parts required for purchase to build a 3D printer. I will break them down as to where I purchased the parts at.
General Full List of Parts
Quantity
|
Item
|
Link
|
Note
|
Purchased
|
1
|
pane of glass 7 7/8"x 7-7/8"
|
None
|
None
|
No
|
1
|
Plastruder
|
[1]
|
1.75mm filament
|
No
|
83
|
5/16" Nuts
|
[2]
|
Stainless
|
No
|
93
|
5/16" Washers
|
[3]
|
Stainless
|
No
|
6
|
5/16" x 30 Fender Washers
|
unknown
|
Stainless
|
No
|
2
|
M4 x 20 Bolt
|
Link
|
Note
|
No
|
2
|
M4 Nut
|
Link
|
Note
|
No
|
2
|
M4 Washer
|
Link
|
Note
|
No
|
22
|
M3 x 10 Bolt
|
Link
|
Note
|
No
|
16
|
M3 x 25 Bolt
|
Link
|
Note
|
No
|
4
|
M3 x 40 Bolt
|
Link
|
Note
|
No
|
70
|
M3 Washer
|
Link
|
Note
|
No
|
40
|
M3 Nut
|
Link
|
Note
|
No
|
2
|
M3 Grub Screw
|
Link
|
Note
|
No
|
3
|
608 Roller Skate Bearing
|
[4]
|
Note
|
No
|
6
|
5/16" x 370mm Threaded Rod
|
Link
|
Note
|
No
|
4
|
5/16" x 294mm Threaded Rod
|
Link
|
Note
|
No
|
3
|
5/16" x 440mm Threaded Rod
|
Link
|
Note
|
No
|
2
|
5/16" x 210mm Threaded Rod
|
Link
|
Note
|
No
|
1
|
5/16" x 50mm Threaded Bolt
|
Link
|
Note
|
No
|
2
|
Everbilt 1/2 in. x 1-1/2 in. and 7/16 in. x 2-1/8 in. Zinc-Plated Compression Springs (4-Pack)
|
[5]
|
Needed for the threaded rods
|
No
|
2
|
8mm x 420mm Smooth Rod
|
Link
|
Note
|
No
|
4
|
8mm x 406mm Precision Rod
|
[6]
|
Note
|
No
|
2
|
8mm x 330 mm Precision Rod
|
[7]
|
Note
|
No
|
1
|
225mm x 225mm
|
Link
|
Steel
|
No
|
1
|
140mm x 225mm
|
Link
|
Steel
|
No
|
1
|
840mm x 5mm Belt
|
[8]
|
Rubber
|
No
|
1
|
900mm x 5mm Belt
|
[9]
|
Rubber
|
No
|
5
|
NEMA Bi-Polar Stepper Motor
|
[10]
|
Recommended by Midsouth Makers
|
No
|
50
|
Zip Ties
|
Link
|
Small
|
No
|
1
|
Maker Gear Plastruder
|
[11] - $170
|
Prusa Stepper Plastruder Kit (.35mm hybrid for 1.75mm filament)
|
No
|
2
|
Pully
|
[12]
|
Recommended by Midsouth Makers
|
No
|
1
|
Hobbled Bolt
|
[13]
|
Recommended by Midsouth Makers
|
No
|
1
|
Heated Bed
|
[14] $50.00
|
Recommended by Midsouth Makers
|
YES
|
1
|
RAMPS DIY Kit
|
[15] $162.00
|
Recommended by Midsouth Makers
|
YES
|
A2A Printer Hardware Kit Includes
M3:
|
22 pcs - M3x10 Cap Screw
|
16 pcs - M3x25 Cap Screw
|
04 pcs - M3x40 Cap Screw
|
02 pcs - M3x06 Set Screw
|
70 pcs - M3 Washer
|
40 pcs - M3 Regular Nut
|
M8:
|
83 pcs - M8 Regular Nut
|
93 pcs - M8 Washer
|
06 pcs - M8x30/M10x30 Fender Washers M4:
|
M4:
|
02 pcs - M4x20 Cap Screw
|
02 pcs - M4 Washer
|
02 pcs - M4 Regular Nut
|
Ball Bearing:
|
3 - 608ZZ Ball Bearing
|
T5 Belts:
|
840mm (for Y axis)Width:5mm; Pitch:5mm
|
950mm (for X axis)Width:5mm; Pitch:5mm
|
Springs
|
Spring - 4 pcs
|
8mm Stainless Steel Bar:
|
2x 420mm (x-bar)
|
2x 406mm (y-bar)
|
2x 350mm (z-bar)
|
3.5mm Aluminium Printed Plate
|
1 pcs - 140mm x 225mm
|
1 pcs - 225mm x 225mm
|
M8 Threaded Rod:
|
6x 370mm (three per side)
|
4x 294mm (front/rear)
|
3x 440mm (top/bottom)
|
2x 210mm (z-leadscrew)
|
1x 50mm (x idler)
|
Which leaves the following Parts left to purchase:
5x NEMA 17 Bi-Polar Stepper Motors
|
50x Zip Ties
|
1x MakerGear Plastruder
|
2x Pullys
|
1x Hobbled Bolt
|