3d printer parts

From Unallocated Space
Revision as of 09:14, 19 January 2012 by Hexjunkie (talk | contribs)
Jump to navigation Jump to search

This is the list of parts required for purchase to build a 3D printer. I will break them down as to where I purchased the parts at.

General Full List of Parts

Quantity Item Link Note Purchased
1 pane of glass 7 7/8"x 7-7/8" None None No
1 Plastruder [1] 1.75mm filament No
83 5/16" Nuts [2] Stainless No
93 5/16" Washers [3] Stainless No
6 5/16" x 30 Fender Washers unknown Stainless No
2 M4 x 20 Bolt Link Note No
2 M4 Nut Link Note No
2 M4 Washer Link Note No
22 M3 x 10 Bolt Link Note No
16 M3 x 25 Bolt Link Note No
4 M3 x 40 Bolt Link Note No
70 M3 Washer Link Note No
40 M3 Nut Link Note No
2 M3 Grub Screw Link Note No
3 608 Roller Skate Bearing [4] Note No
6 5/16" x 370mm Threaded Rod Link Note No
4 5/16" x 294mm Threaded Rod Link Note No
3 5/16" x 440mm Threaded Rod Link Note No
2 5/16" x 210mm Threaded Rod Link Note No
1 5/16" x 50mm Threaded Bolt Link Note No
2 Everbilt 1/2 in. x 1-1/2 in. and 7/16 in. x 2-1/8 in. Zinc-Plated Compression Springs (4-Pack) [5] Needed for the threaded rods No
2 8mm x 420mm Smooth Rod Link Note No
4 8mm x 406mm Precision Rod [6] Note No
2 8mm x 330 mm Precision Rod [7] Note No
1 225mm x 225mm Link Steel No
1 140mm x 225mm Link Steel No
1 840mm x 5mm Belt [8] Rubber No
1 900mm x 5mm Belt [9] Rubber No
5 NEMA Bi-Polar Stepper Motor [10] Recommended by Midsouth Makers No
50 Zip Ties Link Small No
1 Maker Gear Plastruder [11] - $170 Prusa Stepper Plastruder Kit (.35mm hybrid for 1.75mm filament) No
2 Pully [12] Recommended by Midsouth Makers No
1 Hobbled Bolt [13] Recommended by Midsouth Makers No
1 Heated Bed [14] $50.00 Recommended by Midsouth Makers YES
1 RAMPS DIY Kit [15] $162.00 Recommended by Midsouth Makers YES

A2A Printer Hardware Kit Includes

M3:
22 pcs - M3x10 Cap Screw
16 pcs - M3x25 Cap Screw
04 pcs - M3x40 Cap Screw
02 pcs - M3x06 Set Screw
70 pcs - M3 Washer
40 pcs - M3 Regular Nut
M8:
83 pcs - M8 Regular Nut
93 pcs - M8 Washer
06 pcs - M8x30/M10x30 Fender Washers M4:
M4:
02 pcs - M4x20 Cap Screw
02 pcs - M4 Washer
02 pcs - M4 Regular Nut
Ball Bearing:
3 - 608ZZ Ball Bearing
T5 Belts:
840mm (for Y axis)Width:5mm; Pitch:5mm
950mm (for X axis)Width:5mm; Pitch:5mm
Springs
Spring - 4 pcs
8mm Stainless Steel Bar:
2x 420mm (x-bar)
2x 406mm (y-bar)
2x 350mm (z-bar)
3.5mm Aluminium Printed Plate
1 pcs - 140mm x 225mm
1 pcs - 225mm x 225mm
M8 Threaded Rod:
6x 370mm (three per side)
4x 294mm (front/rear)
3x 440mm (top/bottom)
2x 210mm (z-leadscrew)
1x 50mm (x idler)

Which leaves the following Parts left to purchase:

5x NEMA 17 Bi-Polar Stepper Motors
50x Zip Ties
1x MakerGear Plastruder
2x Pullys
1x Hobbled Bolt